IHome iDN45 Operations Instructions download pdf (Page 7)

Listening to Radio

Listening to iPad, iPhone or iPod Using the Dock or USB Port

Sure Alarm

The unit has a sure alarm feature so the buzzer alarm still sound in the event of a power failure, if the backup battery is

installed (see page 7). If your iPad/iPhone/iPod has no sound for 35 seconds or is not present, the unit will switch to

buzzer alarm automatically.

Setting up the Antenna

Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.

Tuning and Playing the Radio

1. Press and release the Mode Button as needed to cycle through Dock, USB, FM radio and Aux-in modes.

2. When FM mode is selected, press the + or – Button to tune the radio to a desired station. The current radio frequency

appears in the lower right of the display. Press the + or – Button for a few seconds to scan for the next clear station.

3. To memorize a station as a preset:

A. Press the Radio Presets Button as needed to step through the 6 presets (P1 - P6) to the number you wish to

assign, and then hold the Radio Presets Button until the selected preset number begins flashing in the display.

B. Press the + or – Button to tune the radio to a desired station. Hold briefly to have the radio autoscan/search for the

next clear station.

C. Press the Radio Presets Button to confirm the setting, two confirmation beeps will confirm the setting and the

preset number you wish to assign. Repeat steps A-C to preset up to 6 stations.

4. To listen to a preset station, press the Radio Presets Button to choose the desired preset.

5. Press the or Button on the unit to adjust the system volume.

This unit features both a 30-pin dock (located on top of the unit) to play and charge iOS devices equipped with the older

30-pin connector AND a USB port (located on back of the unit) which can play and charge both older iOS devices (such

as iPhone 4, iPod touch, etc.) AND Lightning devices such as the iPhone 5 using the charging cable that came with the

device.

Play and pause a device connected to the 30-pin dock using the Dock Button, and play and pause a device

connected to the USB port using the USB Button. Only one device can play at a time. Directions below apply to

whichever dock/port you wish to control. NOTE: The USB port will NOT charge iPad models.

1. Connecting using the 30-pin Dock: Dock an already playing iPad, iPhone or iPod in the 30-pin dock on top of the

unit. The unit will automatically turn on and you will hear the audio playing from your iPad/iPhone/iPod.

Connecting using the USB port: Connect your iPad, iPhone or iPod to the USB port located on back of the unit using

the USB charging cable that came with it.

2. When an iPad/iPhone/iPod is docked to the 30-pin dock or connected to the USB port and in standby mode, press the

Dock Button or USB Button on the unit to play the iPad/iPhone/iPod. If the unit is already on, press and release

the Mode Button as needed until “Dock” or “USB” appears on the lower part of the display, indicating which dock/port

on the unit is in iPod mode.

3. Press the Dock Button or USB Button on the unit on the unit to pause play; press again to resume play.

4. Press the + or – Button on the unit to go to the next or previous track. Press and hold while track is playing for high

speed forward or reverse music search of the current track.

Adjusting Sound on the Unit

You can adjust the sound on the unit while listening to any sound source.

1. Press the or Button on the unit to adjust the system volume.

2. Press and release the EQ Button as needed to select Treble, Bass, Balance or 3D sound effect, then press the + or

– Button to adjust settings.

TIP: You can also adjust EQ with the iHome Set app.

1 2 3 4 5 6 7 8 9 10 11 12 13

Comments to this Manuals

No comments

IHome iDN45 Operations Instructions Page 7

Comments to this Manuals

Related products and manuals for Docking speakers IHome iDN45